常熟市航宇玻纖絕緣材料有限公司江蘇馳揚新材料科技有限公司 從事各類高低壓絕緣套管的制造商
咨詢熱線：
18901572979
常熟市航宇玻纖絕緣材料有限公司
|
項 目 Item |
硅樹脂玻璃纖維套管 Silicone Rubber Sleeving |
|
連續使用溫度（℃） Temperature Endurance |
-60℃+200℃ |
|
耐溫性（℃） Temperature Endurance |
200℃±2℃，168h≥1/2 原電壓值 |
|
熱老化 Aging Test |
260℃,6小時，無裂紋 260℃,6h, No Cracking |
|
冷彎曲 Cold Bend |
無裂紋 No Cracking |
|
水平燃燒 Horizantal Flame Test |
≤30秒 ≤30 S |
|
燃燒性 Flammability |
VW-1 |
|
絕緣電阻-室溫下 (Ω.cm) Insulation resistance - at room temperature(Ω.cm) |
≥1011 |
|
涂層耐水解性 Hydrolysis resistance of coating |
涂層與紙或軟管試片之間無粘著，紙無任何變色跡象。 |
|
型號 Type |
測試條件 Testing Condition |
平均電壓 Average（V） |
個別值（伏） Individual Valune (V) |
| 1.5KV | GB/T7113.5 | ≥1500V | ≥800V |
| 2.5KV | GB/T7113.5 | ≥2500V | ≥1800V |
| 4.0KV | GB/T7113.5 | ≥4000V | ≥2500V |
| 7.0KV | GB/T7113.5 | ≥7000V | ≥5000V |
|
規 格 Size |
內 徑 公 差 Tolerance （mm） |
壁 厚 （T） (mm) |
|||||
| 2.5KV | 4.0KV | 7.0KV | |||||
| 1.5KV | |||||||
| 最小值 | 最大值 | 最小值 | 最大值 | 最小值 | 最大值 | ||
| 0.5-2.0mm | +0.20/-0 | 0.2 | 0.35 | 0.3 | 0.45 | 0.4 | 0.5 |
| 2.5-3.0mm | +0.3/-0 | 0.3 | 0.4 | 0.4 | 0.5 | 0.45 | 0.55 |
| 3.5-5.0mm | +0.3/-0 | 0.3 | 0.5 | 0.4 | 0.6 | 0.5 | 0.6 |
| 6.0-9.0mm | +0.3/-0 | 0.3 | 0.55 | 0.45 | 0.6 | 0.55 | 0.65 |
| 10.0-12.0mm | +0.5/-0 | 0.4 | 0.6 | 0.5 | 0.7 | 0.6 | 0.7 |
| 13.0-20.0mm | +0.80/-0 | 0.45 | 0.7 | 0.55 | 0.7 | 0.65 | 0.8 |
| 22.0-35.0mm | +1.0/-0 | 0.65 | 1 | 0.65 | 1.05 | 0.65 | 1.1 |
|
疵點名稱 Flaw |
檢驗標準 Test Standard |
判定 Determinant |
|
油紗 Oil Yarn |
深油紗連續 2-3 圈為一疵點，不連續 100m 5 個以內； 50m、25m 4 個以內 Continuous 2-3circles to be a fault if deep oil yarn;if ncontinuous,not beyond 5circles in 100m;not beyond 4circles in 30m |
合格 Qualified |
|
污漬 Blot |
點狀 5 點,塊狀 3-6mm 一處，100m 允許 5 個，50m,30m 允許 4 個 There are 5 punctate&3-6mm lump in one blot;allowing 5 blot in 100meter;4 in 30m or 50m |
合格 Qualified |
|
氣泡 Bubble |
肉眼能看出的密集氣泡,每長 3cm 作一疵點,100m 允許 5 個，50m,25m 允許 4 個 The intensive bubble through eyes;to be fault if reaching 3cm;allowing 5 faults in 100m;4faults in 25m&50m |
合格 Qualified |
|
漆 塊 Paint Piece |
凸出漆管壁厚一倍，100m 5 個以內，50m、25m 4 個以內 Outstanding twice more than the usual ;within 5faults in50meter;within 4faults in 25m; |
合格 Qualified |
|
毛刺 Burr |
套管表面尖刺高平面 2mm,平面寬 2.5mm，100m 允許 10 個，50m,25m 允許 7 個 Burr 2mm higher than surface ,2.5mm wider than surface;allowing 10 in 100m;7 in 25m&50m |
合格 Qualified |
|
扁管或扭曲 Flat or distortion |
輕微滿足內徑要求不影響外觀和性能的扁管或扭曲判定為合格，嚴重扁管和扭曲影響內徑和性能的判定為 NG It is qualified if flat&distortion meet the ID&OD and physical appearance request;not qualified if influence the ID&Function |
合格 Qualified |
|
刮漆或涂漆不均 Uneven Painting |
不影響外觀及電壓，3cm 記一個次點，100m 允許 5 個，50m,25m 允許 4 個 Not affect the appearance and voltage;3cm to be fault ;allowing 5 in 100m;4 in 25m&50m |
合格 Qualified |
|
長度 Length |
1.切管長度：100m+2m/-0m;50m,30m+1m/-0m;1m+8mm/-2mm 2.(1200v～2500v)短管 6mm-50mm±1mm;50mm-100mm±2mm; 100mm-250mm± 3mm;250mm 以上±4mm; 3.硅樹脂 4kv～7kv 短管：6mm-50mm±1.5mm;50mm-100mm±3mm;100mm-200mm ±4mm;250mm±5mm; 1.Cutting length: 100m+2m/-0m;50m,30m+1m/-0m;1m+8mm/-2mm 2.Tolerance(1500v-2500v):6mm-50mm±1mm;50mm-100mm±2mm; 100mm-250mm±3mm;250mm above±4mm; 3.Silicone Resin:4kv-7kv;Tolerance： 6mm-50mm±1.5mm;50mm-100mm±3mm;100mm-200mm±4mm;250mm±5mm; |
合格 Qualified |
